The use of garden machinery, you must read the instructions in detail, in order to understand the mechanical structure and working principle, better use and maintenance of machinery. Please note: the machine for a few strokes to distinguish.
Use and maintenance of 1, four stroke mower
1. Use unleaded gasoline no more than 90. Never use leaded gasoline, mixed gasoline, or contaminated gasoline. (Note: refueling should be in the outdoor, refueling, absolutely not allowed to smoke, the engine is absolutely not allowed to refuel when running. ) engine oil should use SC grade gasoline engine oil. No use of four stroke motorcycle oil.
2 、 the new mower must be used for 2-3 hours before running. Every 45-60 minutes running, the machine should be stopped for 5-15 minutes. After running in, you must replace the oil and refill the new oil. Do not exceed the upper limit of the gauge mark, but never lower than the lower limit. Always check the oil level before each use. Change the oil every 30 hours (preferably in a heat engine).
3, each use should check the filter core, the machine every 30 hours to replace or clean paper filter core, cleaning sponge filter core, serious pollution, should be washed or replaced in advance.
4 、 the machine should be shut down for 5-15 minutes every 45-60 minutes. The engine and chassis must be cleaned after each use of the machine.
5, it is forbidden to use in more than 25 degrees slope, causing the oil splashed enough oil for the wheel angle is too large, there will be the cylinder (or lock).
6, use the machine before you clean up debris in the lawn, such as stone tile, wood, wire, nozzle, materials such as steel.
Safety first！ Maintenance of three points: "look, an oil filter, the chassis"
Use and maintenance of two, two stroke Hedgerow machine, cutting machine and cutting saw
1. Use unleaded gasoline 90 or more, and use two stroke gasoline engine oil for motorcycles. No use of pure gasoline.
2, the machine uses gasoline and diesel oil mixed fuel, gasoline and engine oil volume mixing ratio is 20-25:1.
3, the new machine must be used before running 1 hours, every 20-30 minutes running, the need to stop for 5-10 minutes.
4, every 20 hours, you must gear box, gearbox, work first class to add butter.
5, every 40 hours after the use of the machine, must check each screw is loose, such as loose, please be sure to tighten.
6, use the machine before cleaning the work site, to prevent the presence of stones, wires, and other debris, affecting the use of safety.
7, hedge trimmer blade maintenance: regular (25 hours) under the blade clearance inspection, and timely adjustment (bolt interval of half circle thread interval), keep a sharp edge. Add oil to the blade every hour of work and trim the diameter of the branches less than 10mm.
8, brush cutter blade maintenance: nylon rope should control the length of less than 15cm, with a blade, the blade should ensure the balance of rod vibration do not use the vibration of the blade.
Safety first！ Maintenance of three points: "a mixture of oil, butter, filter and two three blade"
Three, other attention:
1 all machine working conditions must be added to the big throttle.
2, the machine appears abnormal sound, vibration and fault, should promptly notify the dealer.
3 when maintenance and maintenance, when moving the machine, the engine should be stopped and the spark plug wiring should be removed.
4, strictly prohibit the use of minors. Do not move your hands and feet closer to the running part, especially the blade, so there are many instances of problems.
5, when the machine tilted, should be tilted to the side of the muffler, filter above.
Safety first！ Three points: "people are the first, maintenance is stronger than repair, work must be serious.""
Four, winter maintenance (long-term maintenance, storage period of more than 30 days) notice:
1, release the gasoline in the tank, and then start the gasoline engine until the gasoline is exhausted and shut down;
2, in the heat engine just stopped, the first release of crankcase oil, immediately filling new oil to the appropriate scale;
3. Remove the spark plug and drop 5-10 ml of oil into the cylinder. Turn the crankshaft ring and fit the spark plug;
4. Clean the cutter head, engine block, cylinder block, cylinder head heat sink, wind shield, net cover and dust and debris around the muffler. Then, save it